PAT TRAP WIRING DIAGRAM
Pat-Trap Technical Information – Pat-Trap, Inc.
Singles & Doubles Angle: It is recommended that you mark the elevation cog at 20° for singles and 23° for doubles, at 45-51 yards at 9 feet elevation, using a protractor. Wobbles Angles: Left/Right Angle = 8” => 50° , Left/Right Angle = 10” = 60°, Down Angle = 7° Min, Up Angle = 25 ½° Max. Parts-list-with-Pictures.632 Western Ave, Henniker, NH 03242 · (603) 428-3396DIRECTIONSWEBSITE
Pat Trap Replacement Parts | Trapshooters ForumwwwshootersPat trap problems | Trapshooters ForumwwwshootersFor Sale, used Pat Trap with acessories. $2250wwwicantrapshooterQuality Replacement Parts Online Store: Pat Trap PartswwwityreplacementpartsSetting up ATA field | Americantrapshooter - The open twwwicantrapshooterRecommended to you based on what's popular • Feedback[PDF]
INSTALLATION - SAFETY - MAINTENANCE MANUAL
PAT-TRAP, Inc. *Choice of the ATA* 632 Western Avenue • Henniker, New Hampshire 03242 • Tel. (603) 428-3396 • Fax (603) 428-7340 5 Diagram 5 PAT-TRAP® SERIAL NUMBER LOCATION Measurements of the Pat-Trap machine From the bottom of the base to the top of the King Pin 24” From the bottom of the base to the top of the turret 34 ¾ “People also askWhat is the SW serial number for a Pat trap?What is the SW serial number for a Pat trap?Manual For Pat Trap “SW” Series Serial Nos. 1 through 2417 SR INSTALLATION - SAFETY MAINTENANCE Manual Singles To Doubles In Seconds! Serial # H 1 through sw 2417 x}? Date: WARNING This Manual discloses details of a patented apparatus or device for throwing clay targets.Manual For Pat Trap “SW” Series Serial Nos. 1 through 2417 SRSearch for: What is the SW serial number for a Pat trap?How do you adjust a Pat trap double handle?How do you adjust a Pat trap double handle?ADJUSTMENT FOR PAT-TRAP®DOUBLES The adjustment for Doubles should only need to be done the very first time the machine is used. Using a 7/16” wrench, loosen the bolt, move the Double Finger in 1/8” increments.The PAT-TRAPSearch for: How do you adjust a Pat trap double handle?How do I use the Pat-trap® machine?How do I use the Pat-trap® machine?The PAT-TRAP®machine must be released and turned off before performing any work. Rotate the bumper 45 degrees (1/8thturn) after approximately 100,000 throws (see counter located in the Electrical Control Box) to see if a flat spot is visible. The bumper should be easy to rotate by hand without having to loosen the bolt.The PAT-TRAPSearch for: How do I use the Pat-trap® machine?How do you use a target brush on a Pat trap?How do you use a target brush on a Pat trap?The purpose of the target brush is to hold the target against the throw arm when the throw arm advances to the cocked position. When the brush begins to “flair out”, loosen the screw and turn the brush 180 degrees. The brush needs to be aligned with the narrow side of the brush running from front to back of the Pat-Trap®The PAT-TRAPSearch for: How do you use a target brush on a Pat trap?Feedback[PDF]
The PAT-TRAP - Golden West Ind
Diagram 4 Diagram 5 A fully crated Pat-Trap is 420 #. Machine and pump weighs 350 #. Turret weigh 50 #. Pump weight 50 #. Pat-Trap machine w/o pump and turret weight 250 #. 43” The Serial Number is stamped on the edge of the ¼” steel plate. notch Measurements of the Pat-Trap machine From the bottom of the base to the top of the King Pin 24File Size: 4MBPage Count: 60[PDF]
Pat-Trap G Series Manual - Quality Replacement Parts
(Diagram 8) View from back of trap elevator Switch #5 Red Wire (NO.) (Diagram 10) Magnet Activator and Throw Arm Limit Switch Turret Activator Switch (Diagram 7) Turret Deactivator switch Black Wire (N.C.) (Diagram 9) Pullcord Button Switch #1 Rev, 6/01 Switch #2 Black Wire (N.C.) Switch #3 Red Wire (NO.)File Size: 8MBPage Count: 83
Pat-Trap, Inc. – Trap and Skeet Machine
Since that first machine all of us at Pat-Trap, Inc. strive for the best overall Trap and Skeet machines in the business, because we were trap shooters first. We pride ourselves with our prompt and courteous customer service. You will never get an answering service during business hours 8:00-3:30 EST. Since becoming the “Official SupplierMissing:wiring diagramMust include:wiring diagram[PDF]
Manual For Pat Trap “SW” Series Serial Nos. 1 through 2417 SR
TURNING THE PAT-TRAP@ MACHINE "OFF" Standing outside and to the side of the trap house; push the On/OfffRelease toggle switch all the way down to release. The trap will throw the target and not cock the spring. Push the Motor toggle switch down to the OFF position LOADING THE MACHINE The PAT-TRAP@ machine holds four (4) full cases of clay targets.[PDF]
PAT-TRAP - Donuts Inc.
PAT-TRAP, Inc. *Choice of the ATA* 632 Western Avenue • Henniker, New Hampshire 03242 • Tel. (603) 428-3396 • Fax (603) 428-7340 13 SKEET SWITCH ID Switch A PAT-TRAP Pump Motor Switch (Diagram 7) Switch B PAT-TRAP On/Off/Release Switch (Diagram 7) Switch #1 Skeet release switch (Diagram 9)
Pat Trap Traps
Base Dimensions: 30" W x 21.5" L. Height Requirements: 41" (Minimum) to 43" (Preferred) from pedestal to ceiling inside trap house. Use with manual pull cord or accepts most voice or wireless release systems. No gearboxes to break down or complex electronics that overheat. No more target guide springs to create target dust for cleaner operation.
Pat Trap service and repair question | Page 2 - Trapshooters
Oct 09, 2020Sanding the rust off the plate and wipe it down with silicone ragk the switches against the wiring diagram are normally closed and some are normally open ohm meter is your friend. Download the manual from pat for the measurements and adjustments this is some help.
Manuals - Shooting Equipment, Outdoor Range Design
Serial #'s 6305 and Newer. Serial #'s 1-2416. Skeet Sets. Serial #'s 2417-6305. Product Manuals. Personal Use. Wobble Machines. Sporting Machines.
Related searches for pat trap wiring diagram
pat trap replacement partspat trap manualpat trap troubleshooting g seriespat traps pricespat trap machinespat trap adjustmentspat trap problemspat trap pinion timing